Pneumatic Cylinder
Pneumatic Cylinder
We'll take the lead in delivering great solutions to improve your productivity.

KTXF

▶ Significantly lower height by integrated  design of cross roller guide and cylinder 

▶ Excellent straightness and anti-rotation  for precise environments 

▶ The cylinder can be mounted from two directions 

▶ Piping can be connected from two directions

KRQ

▶ Rack & Pinion type 

▶ Double-cylinder structure doubles output 

▶ Easy handling of wiring with hollow shaft 

▶ Choose from 2 cushions

KTXH

▶ It is a miniature linear ball bearing integrated cylinder

▶ It has excellent straightness and anti-rotation, so it is suitable for precision assembly

▶ There is a slot for attaching an auto switch

▶ In a two-way, can attach the work

▶ In a three-way, can connect the pipes

▶ In a four-way, can attached the cylinders

AFC, ADFC

▶ Compact installation space due to shorter tube length compared to the existing thin cylinder

▶ The thin cylinder is optimal for press fit, clamp and short stroke

▶ The exterior of the body is specially anodized to give it a beautiful appearance

▶ Both ends tapped type and through hole type can be selected for mounting type

KAHB Hot

Hot

▶ With pneumatic pressure, large-capacity high pressure and low hydraulic pressure can be obtained

▶ With the pneumatic valve, it is possible to simply operate the two-stage discharge operation of rapid feeding and increasing pressure feeding

▶ It is possible to adjust the hydraulic pressure steplessly by pneumatic adjustment

▶ Less air consumption to get the same output power

▶ Stable operation is possible because there is no increase in oil temperature

▶ The unique structure does not require air mixing or air bleed operation

KTXQ Hot

Hot

▶ High precision and high rigidity are realized by anti- rust and dust-proof by linear ball bearing method 

▶ Adjusters (option) can be attached on both sides

▶ Workpieces can be attached in two directions

▶ Auto switch can be attached to slot

▶ The output is doubled with the dual load method

▶ The cylinder can be mounted from three directions 

KRC Hot

Hot

● Auto switch can be mounted on four sides without protruding 

● Left, right direction selectable

● Installation methods vary (Piercing, Tab Attachment, Flange Attachment)

● Strong Scraper Basic Mounted (20Ø Not Mounted)

KTXS Hot

Hot

▶ High precision with Cross roller bearing method 

▶ Adjusters(Option) can be attached on both sides 

▶ Workpieces can be attached in two directions

▶ Auto switch can be attached to slot

▶ The output is doubled with the dual load method

▶ The cylinder can be mounted from three directions 

ACI Hot

Hot

▶ ISO15552 (original ISO6431) standard cylinder

▶ Sturdy wear ring provide a long service life and low start up pressure

▶ The Aluminum profile without tie rod provides excellent corrosion resistance, and has an auto switch groove for easy attachment

▶ The cushion adjustment is smooth and stable

.

ACI, KCC, SMC, TPC, PISCO, F.TEC, AIRTAC, Pneumatic, Cylinder, Air, General

AJP2 Hot

Hot

▶ Compact & lightweight makes it easier to install and dismantle

▶ Piston rod is highly precise and do not require refueling

▶ attachable the auto switch

▶ The cylinder body has a switch slot, so it's easy to attach

.

AJP2, KCC, SMC, TPC, PISCO, Pneumatic, Cylinder, Air

KCKP Hot

Hot

▶ Four types arm are available

▶ It can mounted on the four sides available

▶ Rod crank slider structure

▶ It is easy and convenient to change the opening angle 

KPG01 Hot

Hot

▶ Increased efficiency design with piston at the bottom

▶ Sensor is applicable with embedded neodymium magneton the piston

▶ Improved hardness and lubrication with no magnet on the guide rack

▶ With pin hole for body and jaw positioning


KAGL Hot

Hot

▶ Angular type air gripper

▶ Auto switch is attachable

▶ Hard anodizing on the body to improve surface hardnessand durability

▶ Dust cover can be attached

▶ The structure of 4 tabs and 2 pins at the bottom of themain body allows for a solid installation


KAGS Hot

Hot

▶ Angular type air gripper

▶ Auto switch is attachable

▶ Hard anodizing on the body to improve surface hardnessand durability

▶ Dust cover can be attached


KBG-SD Hot

Hot

▶ Dual piston type with rack & pinion principle

▶ Increased efficiency design with piston at the bottom

▶ Sensor is applicable with embedded neodymium magneton the piston

▶ Improved hardness and lubrication with no magnet on the guide rack

▶ With pin hole for body and jaw positioning

▶ SD1 type is built-in wearing to improve durability and it is strong against buckling load by increasing the guide roddiameter.